Home Cleaning Tips Can I Clean a Laptop Computer That Was Exposed to Mold?

Can I Clean a Laptop Computer That Was Exposed to Mold?

by Catherine

My Tips and Techniques for Cleaning the Dust and Mold Out of Your Beloved Take-Along Device

One of the questions I get most often via email or through the blog is whether  or not you can clean laptop for mold after an exposure. This is a difficult topic to address, since laptops pose the unique situation of being both non-porous (smooth, hard surfaces) and semi-porous (they allow air to circulate through them, and some have many contours such as carvings). To some, a laptop computer seems like it should be easy to clean. Unfortunately, laptops and desktop computers with inner fans and air flow, cooling mechanisms make them particularly difficult to remediate successfully. (Note: Desktops are one of the hardest electronics to clean, because the dust inside can be overwhelming even when mold exposure isn’t a factor. It is best to adopt a practice of using your HEPA vacuum with a soft brush attachment to clean the outside of the computer casing and the fan vents once a week to thwart dust build-up from a mold prevention standpoint.) As a matter of fact, none of our computers were not able to be saved after our mold ordeal. I must have cleaned each one at least four different times before I finally gave up and threw them out. It was definitely a sad and expensive loss.

Now that I have more knowledge and experience with mold, I know that the biggest hinderance to my success was not what I was using to clean the computers, but, rather, the way that I was attempting to clean them. I was not fully addressing all of the mold and dust trapped inside within the fan. Thus, I was never able to get them to a place where I could turn them on and not have an almost immediate reaction—sneezing, headaches, skin rashes, and itchy, watery eyes. It was as if the mold spores were still actively circulating inside the computers no matter what I did. At the time, I definitely did not know as much as I know now about mold and cleaning for mold, so my “tool belt” wasn’t as stocked with options and ideas of other ways to clean them besides continuously wiping them down, blowing out the fans with an air compressor, and trying to allow them to run in outdoor environments to essentially blow the mold spores out from continual use. Admittedly, not the best strategy.

Let’s be honest, even when unhealthy levels of mold and mold illness are involved, a computer is a large expense. Computers are also very personal items, and if you can avoid having to replace or repurchase one, most people want to—regardless of the mold danger. I am here to tell you, though, that of all potentially contaminated items that you should try to not introduce to a “safe,” mold-free space, a computer is a big one, for the very same reason that it is hard to clean—its inner fan. This fan, and cooling system, if full of mold spores can swiftly deposit mold all over your things and home in a manner of minutes. Thus, it is never a good idea to remove computers or electronics from a mold-contaminated home and to continue to use them without proper and targeted cleaning, as well as testing when the cleaning is complete to make sure that it actually worked.

That is precisely why I am bringing this post to you today. I have been working on a “new” technique for cleaning computers or other fan-based electronics for mold. I think I have finally found the best way to clean a laptop specifically and I want to share it. Although I don’t have a mold-contaminated computer to TAP test, clean, and TAP test again to see how well this technique worked at this point in time, I think the sheer amount of dust and dirt that I was able to remove is evidence that you will find a great deal of success with this method, if you follow it step-by-step, and use proper protective gear while doing so.

(Note: For this job, proper protective gear, since I am assuming that those doing this are dealing with a computer that is mold contaminated, should consist of disposable gloves, clothing that you can throw away, or wash immediately with EC3 Laundry Additive, eye protection, and a N-95 respirator mask. I would even go for a half respirator mask, if you are very sensitized. You should also do this outside in the open and should never try to clean any contaminated items inside your home or anywhere that you are living and that is free of mold. Any items that have not been properly remediated should always be kept in air-tight plastic containers, and should be stored outside of your safe indoor space. Once properly remediated, and you either have a successful TAP test (culturing 0-2 colonies), or have zero reaction to the computer when turned on and running, you can bring it back into your home and make it a part of your life again. If you cannot get a clean TAP test or still react to the computer after cleaning it, it is best to cut your losses and dispose of it. No matter what, I have accepted, and I think you should too, that there are just some items that cannot be successfully cleaned, no matter what you do. In other words, there are always outliers. Thus, I encourage you to try your best to save those things that really matter and are important to you, but to also be ready and open to letting things go for the sake of your health, if your efforts do not yield positive results.)

How to Clean a Laptop Computer for Mold:


  • Make sure your laptop is unplugged and not connected to any power source.
  • Place laptop on a hard surface, covered with a towel for cushion.
  • HEPA vacuum all outside surfaces of the computer. You should be careful to get in between the keys and to remove any visible dust or dirt from all exposed spaces.
  • Blow compressed air through fan exhaust and throughout the unit.



  • Saturate a clean, lint-free dusting cloth with alcohol. Wipe all outside surfaces and keys with the alcohol. You are using it as a disinfectant and to remove any bacteria. Bacteria are also a huge issue with sickness and computers, so you also want to address this while cleaning it.

(Note: Researchers have discovered that computer keyboards contained 7,500 bacteria per swab – much more than an average toilet seat, which has 5,400. James Francis, the microbiologist who carried out the research, said: “A count of 600 on a plastic device of any sort is incredibly high.”)

  • Flip your laptop upside down and using the screwdriver, carefully remove the bottom panel of your laptop. Different manufacturers construct different types of laptop enclosures, but most employ screws that can be removed with a small Philips-head screw driver. The processor fan should be plainly visible once the inside of the laptop is exposed.

  • Hold the fan in place with your finger, so that it does not rotate while you clean it. Never remove the fan, because removing parts without advanced knowledge of the hardware could damage the processor or its heat dissipators.
  • Saturate the other dusting cloth with EC3 Mold Solution Concentrate or EC3 Mold Spray.
  • Clean the face of the fan with the cloth, gently rubbing dust and dirt away from the center.
  • Once dry, gently blow compressed air into the fan to dislodge dust that may have fallen into the fan. Repeat the process until the fan is clean.
  • Use the EC3-saturated cloth to clean the underside of the piece that you removed to reveal the fan. This piece can get a lot of dust and debris lodged on it as well, so you need to give it some attention.
  • When finished, and the fan and inside of the computer are bone dry, replace the laptop’s bottom cover.
  • Use the EC3-saturated cloth to clean the exterior of the laptop just as you did before with the alcohol.

Once you have completed this process, you should use EC3 Mold Screening Test Plates, or other mold screening plates available online or from a local home improvement store to test the computer for mold. To do this, open the plate and position it near the back fan of the laptop. Turn the computer on and allow it boot up and run for a few minutes. When the fan is running, pick the laptop up and gently tap the plate against the exterior fan opening. This will ensure that you are dislodging any dust or mold that may still be on the inside and capturing it in the plate media to culture. It is not a perfect method, but one that can still yield viable and helpful results. Close the mold plate, seal it, label it, and cover it with aluminum foil.

The plate will then need to incubate for 5 days—incubation time will ultimately be determined by the manufacturer’s directions for the plates that you use. After the incubation period is up, you can check your results. You can also TAP test the laptop after cleaning it by gently tapping the open mold plate against the laptop to produce a puff of air between it and the plate. This must be done while the computer is running, though to get an accurate picture of whether or not mold is still circulating inside of it. Once you have your test results, you can decide whether or not to keep or dispose of the computer.

(Note: It is my opinion that if you are ill, or know that the computer was exposed to mycotoxin-producing molds, that you should not keep it if you cannot get the mold test plates below 3 colonies after cleaning. This may sound extreme, but even a small amount of carcinogenic mold can keep you very sick.)

I hope you find this information helpful. It definitely never hurts to attempt to clean something, just make sure you are also employing proper testing techniques to make certain anything you are cleaning is safe before bringing it back into your home. Are there any items you are having a hard time letting go of? Specific questions are always welcome. Comment below or email me at catherine@moldfreeliving.com.
Share this:

You may also like


Salma - 4:57 pm

Hi Catherine, what are your thoughts about decontaminating a TV? Have you tried cleaning a TV with the same process as you mention on your site for decontaminating a laptop?
Also, I wanted to know your thoughts about cleaning mildew from jetted water lines of a jacuzzi bathtub with EC3. Can you give me some recommendations on how to do this effectively or do I just need to replace the tub? Thank you!

Catherine - 3:07 pm

Hi, Salma,
I definitely think that some TVs can be effectively cleaned. The EC3 Wipes would make an even better solution than the spray for a television. I would methodically wipe the entire thing down, including the cord so that a thin film of the wipe solution is left behind to air dry. You can use compressed air or a very strong HEPA vacuum tool to either blow or suck out dust from the vents/crevices. For the tub, I would actually recommend using the EC3 Laundry Additive or cleaning peroxide. First, clean the tub throughly using a mild dish soap and a scrubber brush. I say dish soap because you must remove any soap scum, dirt, or oily-type debris that can be left behind. I recommend The Unscented Company Dish Soap. It does not contain any scent or citric acid and works wonderfully. After cleaning, you would then need to fill the tub over the jet line with warm water. Depending on the size of the tub, you will need to pour enough Laundry Additive or cleaning peroxide in to have a fairly high concentration. This may take the whole bottle. Close the valves (if allowed by manufacturer) and run the jets for 15 minutes. This will ensure that your solution is cycling through your jets and not your plumbing. You may have to drain the tub and repeat this if a lot of gunk is coming out. Then fill and run the jets again with the valves open with water and a little of the soap added to it. Then drain the water and wipe down the tub with a cloth that has been soaked in a part alcohol, part Laundry Additive or Mold Solution Concentrate blend, or you can use alcohol or EC3 Wipes. After you get it nice and clean, keeping up on this maintenance routine will make those monthly cleans a cinch.

Regina Robinson - 11:25 am

I rented a unit for a year all my stuff is contaminated land lord not cooperative offed me 700 for everything I own any advice u can give will be great

Catherine - 7:10 pm

Hi, Regina,

This is such a difficult question to answer. Do you have your lease agreement? Do you have testing or pictures or documented proof of the mold and that your landlord did not assist in making the space safe for you or knew of its presence and did not remediate properly? Do you have testing of your belongings or pictures and documentation of what was impacted by the mold and its value? Any receipts or documents from an indoor environmental professional would give you a leg to stand on to demand more to cover your losses. Also, depending on what state you live in, you do have renter’s right and can take your landlord to small claims court if your rights have been violated or if the terms of your rental contract were violated. Renter’s insurance also covers some damages to belongings, but your landlord should also have insurance to cover this. I hope that helps.

Sergio - 1:25 am

Can you charge , for coaching on mold avoidance? I am changing house and would love your recommendation, I live in Mexico

Catherine - 11:41 pm

Hi, Sergio,
I don’t charge for services since I am not a professional. As far as mold avoidance is concerned, true mold avoidance is detailed best by Erik Johnson and on the website: https://paradigmchange.me/ I think you will find a wealth of information there. I do think Erik may do consults or coaching as well.

Lisa - 5:26 am

A computer fan is a very minor expense. It’s a good idea to ground your hand with a copper earthing bracelet when workingvon ekectronics. On a desktop fans are vety easy to swap out. The most difficult part is usually putting back all the cable ties. (You’ll probably need a lot of them, but you can get a variety bag of those.) I recommend you take photos as you undo the fan wiring to the connector. If you then forgot how something fit together you have a photo for reference. For a laptop, since you’re already going for opening it up anyway, youtube will have videos on how to remove the fan for your exact make and model. Sometimes labeled as disassembly or repair video for some other part. It can be a bit tricky, but it can turn tossing something worth a lot of money into a bit of time warching videos, removing some screws, connectors and cable ties and shopping for the right replacement part. I was chuckling when I read a recommendation to use vacuum cleaners and air filter fans to clean a moldy house. Guess where all my air filters and vacuum cleaners are? Also guess what is extremely difficult to clean mold out of? LOL

Catherine - 7:13 pm

HI, Lisa,

Thank you for your recommendations. For the record, I never advocate for using vacuums or air filters as a means of remediation. Those things are tools in an overall house maintenance process, but should never be used alone if there is a mold problem. And, yes, I agree. Air purifiers and vacuums are extremely difficult to clean.

Kat - 9:28 am

Hi Catherine! I cleaned my two laptops that were in my moldy room for about 9 months using your method-I had them professionally cleaned in addition to spraying/wiping them down with EC3 and the EC3 solution was also applied inside. I then tap tested both laptops and the results were 0 colonies. However, I am still having headaches after being in my new space. (I did mold plate testing in the new space and there were barely any colonies.) The laptop charger cords were also cleaned with EC3. In addition to EC3, I also wiped them down with Benefect wipes, which a health consultant introduced me to, and they are supposed to be better at killing the mycotoxins than EC3. My question is are the laptops ok to keep or should I replace them? Is it safe to touch the laptops and their charger cords, or could I be reacting to them still, even after I cleaned them? I’m concerned about the rubber feet on the bottom of the laptop as well, as this material could still have mycotoxins in it, right? Thanks in advance for your help!

Catherine - 12:35 pm

It may not be the laptop you are reacting to. Do you only feel badly in the space when you are using the laptop? Also to note that Benefect contains thymol. I do not always advocate for using it, because many people react to thymol and cannot tolerate it. It causes skin reddening and histamine-type reactions for them. Something to consider. You cannot kill mycotoxins–you can just eliminate them. Thus, continue to clean the laptop and make sure that the internal fan has been cleaned well. If you still feel it is causing you to react, it would be best to replace the computer. Some items just cannot be saved. I hate saying that, but it is the honest truth.

Shauna - 2:25 am

Hi Catherine, what did the mold growing in your laptop or other electronics look like? Particularly in the small crevices like headphone ports or charging ports. I moved from a moldly living environment and brought a laptop with me, and I found a small bit of substance in the headphone port. I’m not sure if it’s mold or dirt so I’m wondering what it looked like in your electronics. Was it slimy/wet or dry and flaky/powdery? What was the color? Thank you very much.

Catherine - 2:55 am

There was no visible mold on my laptop. It was just in the home that made me sick and contained an inner fan. I cleaned it using the method outlined in the article. If there is visible mold and the item is making you sick, I would definitely err on the side of caution and replace it or discard it.

Aaron - 10:49 am

Would you please cite your sources for this article? I want to share them with my functional medicine doctor. Thanks!

Catherine - 2:24 pm

I am the source of the information. This site is my personal blog. I tried 5 different ways to clean laptops and TVs over the years after our mold exposure. The one in the article is the one that worked. I tested it before and after. In my cleaning posts, I am just sharing information that I think will be helpful for others. I took the principles of proper contents remediation and what we know about mold and mycotoxins and applied them to cleaning my computer.

Katie - 10:10 pm

Question regarding computers — I travel for work often and bring my laptop with me into new buildings all the time. In addition, I brought my old laptop into my new apartment after I left my moldy house without realizing I needed to clean it. My question is, what are you supposed to do if you do deal with cross contamination? Seems like this could and will happen all the time?

Catherine - 4:20 am

It can happen at any time. You just have to do the best you can. I try to wipe things down, clean things frequently with products like EC3, and remove things from our home when I react to them. It is a process. There is no way to avoid mold altogether. The goal is to reduce the load.

Alexis Powell - 6:11 pm

I have a toxic mold exposure at work. My family and I are extremely sensitive as we lived in a toxic mold environment for 5 years. We have been out 2 years now and finally have a clean environment but I was sent to work from home because my work is contaminated. I brought my computer with me home. I set up in my garage because I was afraid of contaminating my home but we are all reacting from the computer and screens after I come in the house. Will the spores on this computer become air born in my garage and grow? It is humid in my garage as we live in Florida.

Catherine - 5:01 pm

It can happen. Mold spores only need water to grow. I would keep the computer in a sealed plastic bin. I would not leave it open out there.

Julie - 8:10 pm

Another great article!! Do you know if ozone machines can help clean computers as well. I ran my computer while it was in a plastic tub and ozoned it for 20 minutes. What are your thoughts? It didn’t hurt the computer.

Catherine - 12:51 am

Hi, Julie. I am not a fan of ozone for mold remediation. The science on it just doesn’t indicate that it can removed mycotoxic molds without the additional use of other cleaners or methods. One of the more extensive studies done with ozone and environmental molds concluded the following (all data is available on Pub Med):
There was a significant (p < 0.05) decrease in viable conidia of all three fungi, at ozone concentrations of 5.0-12.8 parts per million, by four hours of exposure. However, in every case, some conidia remained viable even at the highest level of exposure. CONCLUSIONS: These data suggest that ozone must be used in conjunction with other methods of remediation or for more prolonged exposure times in order to eliminate fungal contamination of buildings. I have found that in order to get clean test plates, you have to use a combination of physical cleaning and the correct antifungal products, like EC3 Mold Solution. I hope this helps. Please let me know if you have other questions.


Leave a Comment